Surface Preparation Chemicals for Sale

Smith’s Poly PCF-45 — Concrete Crack Filler & Patch

• Fills cracks, spalls, pop-outs, holes, and voids in concrete
• Fast return to service — grind in 15–60 minutes; heavy traffic in ~1 hour
• Low viscosity — penetrates hairline cracks; extend with sand for deep repairs
• 1:1 mix ratio — easy to measure and mix; no primer needed
• Tenacious bond to prepared concrete (650 psi — the concrete fails first)
• Chemical- and impact-resistant with good load transfer
• Feather edge to any depth (with aggregate extension)
• Interior/exterior, above or below grade — even freezer/chiller floors and radiant-heat floors
• Doubles as a pit grout for polished concrete

Smith’s WB Marking Paint

• Fast return to service — air dries for full traffic in 1–2 hours (even at 50°F / high humidity)
• Durable — accepts forklift and pallet-jack traffic within a few hours
• Ready to use, single component — no mixing, easy to apply
• Excellent UV stability — interior or exterior
• Holds crisp tape-line edges — good bleed-through resistance for clean lines
• Low odor, low VOC, non-flammable — use in all regions
• Good opacity with two coats; may be applied up to 30 mils WFT in a single layer
• Soap-and-water cleanup while wet
• Meets Federal Specification TT-P-1952F Type III

Smith’s Poly-FLEX — Semi-Rigid Resurfacing Compound

• Moisture tolerant — withstands up to 15 lbs (ASTM F1869) and 90% in-situ RH (ASTM F2170)
• Suppresses minor cracks from telegraphing through to the surface
• Flowable and self-smoothing — levels itself for a smooth base
• 100% solids — no solvents, no water, zero VOC, low odor
• High build — applies from 30 mils up to 5 inches neat
• Fast — walkable in ~4 hours to accept the next layer; heavy forklift traffic after an overnight cure
• Freeze/thaw stable — interior or exterior
• Suitable over radiant in-floor heat systems
• Tenacious bond — concrete fails before the bond does (ASTM D4541)
• Strong — 14,010 psi compressive strength; stronger than typical epoxy mortar systems
• Accepts vinyl chip broadcasts directly into the wet film

Smith’s Epoxy FW38 — Primer / Sealer

• Waterborne epoxy primer and sealer — low odor, low VOC, available in all regions
• 38% solids, 2-component
• Penetrates porous substrates — bonds tenaciously to concrete (concrete fails before the bond does)
• Bonds to concrete and wood — a versatile primer across substrates
• Fast cure — typically ~3 hours at 72°F; recoat in a few hours
• Inert to high pH levels
• Soap-and-water cleanup while wet
• Solid colors available with Smith’s WSC Color Packs (sold separately)

Smith’s Poly JF — Semi-Rigid Joint Filler

• Semi-rigid polyurethane — supports and protects joint edges under heavy traffic
• Self-leveling, pourable — easy to place and finish
• 100% solids — zero VOC, low odor, non-tainting
• Fast — shave in 90–120 minutes, diamond grind in ~6 hours, forklift traffic in 8–10 hours
• Moisture tolerant — can be used with Smith’s moisture-mitigation primers on damp slabs
• Bonds tenaciously to concrete, overlays, coatings, tile, and metal
• For joints and repairs up to 5″ deep
• FDA/USDA/CFIA facility acceptable — non-tainting
• No red-label shipping required

Smith’s Epoxy FRM — Fast Repair Mortar

• 3-component, 100% solids epoxy mortar — trowel applied
• Heavy-duty — 10,500 psi compressive strength, 85–90 Shore D hardness
• Fast return to service — heavy/forklift traffic in as little as 8 hours at 72°F
• High impact and abrasion resistance — excellent rolling-load resistance for cart and forklift traffic
• For repairs ≥ 3/16″ — resurfacing, deep patching, joint-wall rebuilding
• Bonds tenaciously — concrete fails before the bond does
• Low odor, low VOC
• Mix in the container — convenient packaging

SSP Camo Patch UV — Polishable Patch & Grout

• UV-proof and non-yellowing — won’t discolor in sunlight
• Translucent — blends into the surrounding concrete
• Extendable — add pigments and dry aggregate to mimic the existing floor
• Self-priming — no separate primer step
• Moisture tolerant
• Non-brittle
• Extended working time — more forgiving to apply
• Fast — grind after 90 minutes, polish after 2 hours
• VOC compliant and certified
• Colorable with iron oxide powders or SSP liquid pigments (Camo Patch UV Color Packs)

SSP Camo Patch UV Color Packs

Available Colors

• #0 Non-Pigment
• #1 White
• #2 Latte
• #3 Tan
• #4 Beige
• #5 Saddle Brown
• #6 Gray Matters
• #7 Anonymous
• #8 Gray
• #9 Black

SSP Joint Seal 600 UV — Polyurea Joint Sealant

• UV-proof and non-discoloring — maintains its color long term (ASTM G-154, minimum change)
• 600–650% elongation — flexes with the joint without tearing or separating
• Aliphatic polyurea — superior UV colorfastness, indoors or out
• Moisture tolerant — cure isn’t affected by ambient moisture
• Self-leveling, 100% solids, 0 g/L VOC
• Extended working time — user-friendly hand mix
• Semi-rigid, rubber-like cured finish; Shore 77A hardness
• Fast — tack-free in 1 hour, shave after 2 hours
• LEED v4.1 compliant; aligns with ACI 302 guidelines

SSP Joint Seal 600 UV Color Packs

Available Colors

• Limestone
• Gray
• Dark Gray
• Anonymous
• Thunderous
• Gauntlet
• Chocolate
• Saddle Brown
• Walnut
• Caramel
• Burnt Sienna
• Sand
• White
• Black